Tiroir à compartiments pour présentoir mural - autorise seulement des parois continues
style of the fingers
space at the start and end in multiple of normal spaces
height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!
space below holes of FingerHoleEdge (multiples of thickness)
extra material to grind away burn marks (multiples of thickness)
width of the fingers (multiples of thickness)
extra space to allow finger move in and out (multiples of thickness)
space between fingers (multiples of thickness)
width of finger holes (multiples of thickness)
angle intérieur des pieds
height of strips to be glued to the inside of bottom edges (multiples of thickness)
height of the feet (multiples of thickness)
distance from finger holes to bottom edge (multiples of thickness)
width of the feet (multiples of thickness)
faire un débord du couvercle sur les côtés (similaire à OutSetEdge)
Régler à la valeur inférieure pour avoir des disques entourant les axes
"outset" ou "flush"
diameter of the pin hole (multiples of thickness)
fixed length of the grips on he lids (multiples of thickness)
thickness of the arc holding the pin in place (multiples of thickness)
diameter of the pin hole in mm
pieces per hinge
number of hinges per edge
style of hinge used
radius of the eye (multiples of thickness)
space between eyes (multiples of thickness)
minimum space around the hinge (multiples of thickness)
width of the "finger hole" in mm
additional pin for better positioning
position(s) of the extra locking springs in the lid
angle of the hooks bending outward
radius at the bottom (multiples of thickness)
length of the hooks (multiples of thickness)
height above the wall
radius of hole
radius of top corner
extend the triangle along the length of the edge (multiples of thickness)
head diameter of mounting screw (in mm)
shaft diameter of mounting screw (in mm)
minimum space left and right without holes (fraction of the edge length)
number of mounting holes (integer)
side of box (not all valid configurations make sense...)
edge style
height above the wall in mm
height of hole(s) in percentage of maximum hole height (handle height - 2 * material thickness)
width of hole(s) in percentage of maximum hole width (width of edge - (n+1) * material thickness)
added to side panels if checked, to front and back otherwise (only used with top_edge parameter)
radius of corners in mm
extend the handle along the length of the edge (multiples of thickness)
type of handle
type of lid to create
height of the handle (if applicable)
height of the brim (if any)
play when sliding the lid on (if applicable)
Textsize in mm for the traycontent
Text Alignment
Distance in X from edge of tray in mm. Has no effect when text is centered.
Distance in Y from edge of tray in mm.
Start compartement labels on the front
Every line is the text for one compartment. Beginning with front left
depth of the hole in mm (in addition to the relative)
width of the hole in mm (in addition to the relative)
maximal radius (in mm)
depth of the hole as fraction of the wall
width of the hole as fraction of the wall width
sections left to right in mm 🛈
sections back to front in mm 🛈
hauteur interieure en mm (si on ne choisit pas « extérieur »)
hauteur des cloisons internes interieure en mm (si on ne choisit pas « extérieur ») (laisser à zéro pour des cloisons aussi hautes que les bords)
treat sizes as outside measurements 🛈
type de bord pour le bord du bas
type de bord pour le bord du haut
additional height of the back wall - e top edge only
radius for strengthening side walls with back_height
Hauteur du trou-poignée en mm
largeur du trou-pignée en mm (zéro pour aucun trou)
add handle to the bottom (changes bottom edge in the front)
Decide which outer walls should have finger hole, too
thickness of the material (in mm) 🛈
format of resulting file 🛈
width of tabs holding the parts in place (in mm)(not supported everywhere) 🛈
Add a QR Code with link or command line to the generated output
print surrounding boxes for some structures 🛈
label the parts (where available)
print reference rectangle with given length (in mm)(zero to disable) 🛈
style for inner corners 🛈
burn correction (in mm)(bigger values for tighter fit) 🛈
Générer Download Save to URL QR Code
