Boxes.py

卡榫样式

space at the start and end in multiple of normal spaces

height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!

space below holes of FingerHoleEdge (multiples of thickness)

extra material to grind away burn marks (multiples of thickness)

width of the fingers (multiples of thickness)

extra space to allow finger move in and out (multiples of thickness)

space between fingers (multiples of thickness)

width of finger holes (multiples of thickness)

内侧角度

height of strips to be glued to the inside of bottom edges (multiples of thickness)

height of the feet (multiples of thickness)

distance from finger holes to bottom edge (multiples of thickness)

width of the feet (multiples of thickness)

两侧有盖子重叠（类似于起始边）

设置为较低的值以获取引脚周围的磁盘

“开始”或“冲洗”

diameter of the pin hole (multiples of thickness)

fixed length of the grips on he lids (multiples of thickness)

thickness of the arc holding the pin in place (multiples of thickness)

销孔直径（mm）

每个铰链件

每个边缘的铰链数量

使用的铰链样式

radius of the eye (multiples of thickness)

space between eyes (multiples of thickness)

minimum space around the hinge (multiples of thickness)

width of the "finger hole" in mm

additional pin for better positioning

position(s) of the extra locking springs in the lid

卡榫样式

space at the start and end in multiple of normal spaces

height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!

space below holes of FingerHoleEdge (multiples of thickness)

extra material to grind away burn marks (multiples of thickness)

width of the fingers (multiples of thickness)

extra space to allow finger move in and out (multiples of thickness)

space between fingers (multiples of thickness)

width of finger holes (multiples of thickness)

angle of the hooks bending outward

radius at the bottom (multiples of thickness)

length of the hooks (multiples of thickness)

高于墙壁的高度

孔半径

顶角半径

extend the triangle along the length of the edge (multiples of thickness)

head diameter of mounting screw (in mm)

shaft diameter of mounting screw (in mm)

minimum space left and right without holes (fraction of the edge length)

number of mounting holes (integer)

side of box (not all valid configurations make sense...)

edge style

height above the wall in mm

height of hole(s) in percentage of maximum hole height (handle height - 2 * material thickness)

width of hole(s) in percentage of maximum hole width (width of edge - (n+1) * material thickness)

added to side panels if checked, to front and back otherwise (only used with top_edge parameter)

radius of corners in mm

extend the handle along the length of the edge (multiples of thickness)

type of handle

type of lid to create

height of the handle (if applicable)

height of the brim (if any)

play when sliding the lid on (if applicable)

内部高度单位mm（除非选择外部）

sections left to right in mm 🛈

sections back to front in mm 🛈

内墙的内部高度，单位为mm（除非选择外部）（与外部墙相同，保留为零）

treat sizes as outside measurements 🛈

additional height of the back wall - e top edge only

radius for strengthening side walls with back_height

add handle to the bottom (changes bottom edge in the front)

thickness of the material (in mm) 🛈

format of resulting file 🛈

width of tabs holding the parts in place (in mm)(not supported everywhere) 🛈

Add a QR Code with link or command line to the generated output

print surrounding boxes for some structures 🛈

label the parts (where available)

print reference rectangle with given length (in mm)(zero to disable) 🛈

style for inner corners 🛈

burn correction (in mm)(bigger values for tighter fit) 🛈