Boxes.py

style of the fingers

space at the start and end in multiple of normal spaces

height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!

space below holes of FingerHoleEdge (multiples of thickness)

extra material to grind away burn marks (multiples of thickness)

width of the fingers (multiples of thickness)

extra space to allow finger move in and out (multiples of thickness)

space between fingers (multiples of thickness)

width of finger holes (multiples of thickness)

Innenwinkel der Standfüße

height of strips to be glued to the inside of bottom edges (multiples of thickness)

height of the feet (multiples of thickness)

distance from finger holes to bottom edge (multiples of thickness)

width of the feet (multiples of thickness)

Deckelüberlappung an den Seiten (ähnlich mit OutSetEdge)

kleinen Wert einstellen, um Bolzen-umgebende Scheiben zu erhalten

"Anfang" or "Bündig"

diameter of the pin hole (multiples of thickness)

fixed length of the grips on he lids (multiples of thickness)

thickness of the arc holding the pin in place (multiples of thickness)

Durchmesser des Bolzenlochs in mm

Gelenke pro Scharnier

Scharnieranzahl pro Kante

Art des verwendeten Scharniers

radius of the eye (multiples of thickness)

space between eyes (multiples of thickness)

minimum space around the hinge (multiples of thickness)

width of the "finger hole" in mm

additional pin for better positioning

position(s) of the extra locking springs in the lid

style of the fingers

space at the start and end in multiple of normal spaces

height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!

space below holes of FingerHoleEdge (multiples of thickness)

extra material to grind away burn marks (multiples of thickness)

width of the fingers (multiples of thickness)

extra space to allow finger move in and out (multiples of thickness)

space between fingers (multiples of thickness)

width of finger holes (multiples of thickness)

angle of the hooks bending outward

radius at the bottom (multiples of thickness)

length of the hooks (multiples of thickness)

Höhe über der Wand

Lochradius

Radius der oberen Ecke

extend the triangle along the length of the edge (multiples of thickness)

head diameter of mounting screw (in mm)

shaft diameter of mounting screw (in mm)

minimum space left and right without holes (fraction of the edge length)

number of mounting holes (integer)

side of box (not all valid configurations make sense...)

edge style

height above the wall in mm

height of hole(s) in percentage of maximum hole height (handle height - 2 * material thickness)

width of hole(s) in percentage of maximum hole width (width of edge - (n+1) * material thickness)

added to side panels if checked, to front and back otherwise (only used with top_edge parameter)

radius of corners in mm

extend the handle along the length of the edge (multiples of thickness)

type of handle

type of lid to create

height of the handle (if applicable)

height of the brim (if any)

play when sliding the lid on (if applicable)

Innere Höhe in mm (außer wenn Außenmaß markiert ist)

sections left to right in mm 🛈

sections back to front in mm 🛈

Innere Höhe der Innenwände in mm (außer wenn Außenmaß markiert ist) (bleibt bei Null wenn Außenwände gleich hoch sind)

treat sizes as outside measurements 🛈

additional height of the back wall - e top edge only

radius for strengthening side walls with back_height

add handle to the bottom (changes bottom edge in the front)

thickness of the material (in mm) 🛈

format of resulting file 🛈

width of tabs holding the parts in place (in mm)(not supported everywhere) 🛈

Add a QR Code with link or command line to the generated output

print surrounding boxes for some structures 🛈

label the parts (where available)

print reference rectangle with given length (in mm)(zero to disable) 🛈

style for inner corners 🛈

burn correction (in mm)(bigger values for tighter fit) 🛈